JL-712B2 is based on ZHAGA BOOK18 interface standard development of intelligent lock type light controller, using light sensing + microwave mobile combination sensor, can output 0~10V dimming signal, at the same time equipped with Bluetooth mesh communication network, can be controlled and configured through APP. The lamp controller is suitable for roads, lawns, courtyards, parks, parking lots, industrial mines and other lighting scenes. It is particularly suited to UFO high-bay luminaires fitted with a Zhaga socket.
| Product type | Zhaga Book-18 interface intelligent lock-type light controller; Bluetooth Mesh communication with 0–10 V dimming output |
|---|---|
| Model | JL-712B2 |
| Power supply | Rated 12–24 VDC; rated current 40 mA |
| Power consumption | < 0.6 W |
| Sensor type | Light sensor + microwave motion sensor |
| Spectral acquisition range | 350–1100 nm, peak wavelength 550 nm |
| Microwave mounting height | 15 m maximum |
| Sensing radius | 6–10 m at 15 m mounting height |
| Anti-jump delay | 3 s — minimum interval before the lamp can be switched on again after it switches off |
| Hold time | Default 30 s, adjustable in the app |
| Stand-by brightness | Default 0%, adjustable in the app |
| Stand-by time | Default 5 s, adjustable in the app |
| Dimming interface | 0–10 V; accuracy ±2% |
| Turn-on illuminance | App adjustable in 5 levels: daytime (any illuminance), dusk ≈60 lx, evening ≈30 lx, night ≈8.2 lx, late night ≈0 lx |
| Energy-saving strategy | Custom |
| Mechanical vibration | IEC 60068-2-6 |
| Flammability level | UL94-V0 |
| Operating temperature | −40 °C to +70 °C |
| Storage temperature | −40 °C to +85 °C |
| Operating humidity | 5% RH to 99% RH |
| Ingress protection | IP66 |
| Dimensions | Φ50 × 36 mm |
| Certification marks shown | CE and RoHS as printed in the datasheet mark row; the datasheet prints no certificate number or standard list |
| Pin | Definition | Function |
|---|---|---|
| 1 | 12–24 VDC | Power input |
| 2 | GND / DIM− | Power input |
| 3 | NC | Not connected |
| 4 | DIM+ (0–10 V+) | Signal output |
Values as printed in the JL-712B2 EN 2305V5 datasheet. CE and RoHS appear in the datasheet as marks only: no certificate number is printed there, so this table reports the mark rather than a certificate. Request the current declaration or certificate copy before quoting compliance in a tender or on a drawing package.
The interface of the product itself has been fool-proof design, the installation only need to tighten the controller directly to the rotatable base, as shown in Figure clockwise after insertion.
The datasheet lists six sockets for this controller: JL-700 (general), JL-700W (without cable), JL-700S (short thread), JL-700T (pin), JL-770 (US / Z10) and JL-710 (built-in 24 VDC power supply). Socket choice follows the luminaire housing thread and whether a local 24 VDC source exists.
No. This model is described as Bluetooth Mesh with app control. Confirm the exact app, supported firmware, provisioning method and gateway requirements; do not infer Casambi compatibility from Bluetooth or Zhaga mounting alone.
The description specifies a 12-24VDC supply and 0-10V dimming. Confirm the low-voltage power source, socket wiring and compatible LED driver using the JL-712B2 instructions; do not apply mains voltage to a low-voltage controller.
Confirm light and microwave sensing settings, mounting conditions, detection coverage, mesh commissioning and IP66 assembly documentation. Voice-platform integration must be confirmed for the actual app, gateway and supported service.
See Zhaga controllers and components, smart lighting controls, and selection and installation FAQs.
Do not worry, we will never spam you.
We will send you the latest cloud-based smart lighting control system manual
